Student Violin Bow
Derhyme
V10201-1
Student Violin Bow
After the violin is a well-known musical instrument, the most important part of the violin is the bow. Many people will ignore this seemingly low-key, thinking it is just an accessory of the violin, but the bow is not as simple as we imagine. Physically, the bow is a small spring system, but from a more rational point of view, the only connection between a person and a stringed instrument must be established by the bow.
Product Advantages
1. Brazil Wood
The bow is easier to shape than the instrument itself. The craftsman first cuts the red board into strips, each of which must have a quadrilateral cross section. To give the bow a certain arc, it is formed in inches by heating with an alcohol lamp until it reaches its standard shape. When it cools down, a radian is formed, and it generally does not return to its original straightness. The bow industry calls this the "wonderful memory of Brazilian mahogany" -- because the spring system is not released for even a year, and if you gently heat it, the bow will quickly return to its original shape. Because this Brazilian wood has feel comfortable, flexibility is beautiful, not easy deform a bit.
2. Mongolian White Horsetail
After manual selection, the Mongolian white horsetail is slightly bleached, which does no harm to the inner and outer structure of the horsetail and has a bright and clean appearance. Therefore, high toughness, sufficient quantity, easy to wear, not easy to break, friction long service life, good timbour effect, about 220 arch hairs. Mongolian white horsetail and natural color horsetail are classy horsetail with beautiful uniform appearance, strong pulling force and plump wool scales, which should not be broken in use. The diameter of each horsetail is between 14 and 20 silvery meters.
3. Enony Tail Bank
Ebony is used as the raw material for the tail bank. It is matched with metal accessories and can be set with clear texture. The bow wool depot is 44-44.5 mm long, 12.5-13 mm wide and 19.5-20.5 mm high. Make sure that the upper grooves fit tightly with the bow rod, the middle gaskets also fit closely with each other, and the T-nut is mounted at the center. After assembly, turning the adjusting screw can make the bow hair tensioned or loosened, which can increase the weight of the bow root.
4. Styling And Coating
Derhyme uses the method of baking bending to finalize the design, through baking to adjust the bow bending and elasticity. Experienced Derhyme workers flexibly master the highest point of the inner arc, ensuring the bending degree and appropriate elasticity of the bow. After the bow head and tail are complete, a protective coat of paint is applied to the outside of the bow shaft. It increases the service life of the bow and will not cause irregular deformation if used for a long time.
Product Specification
Product Name | Derhyme student violin bow |
Product Model | V10201-1 |
Product Size | 4/4、3/4、1/2、1/4、1/8、1/16 |
Bow Material | Brazil wood |
A Hand Material | Sheepskin package |
Tail Bank | Ebony |
Accessories Material | Copper |
Style | Violin bow |
Product Size
Product Show
Product List
Preparation for making violin bow
There are many kinds of wood for making violin bow and bow. You can choose different raw materials according to the grade. In the wood, you first select the material for preparing the rod and then prepare the material. The material preparation is to cut the log into planks. The sawing method is the same as the making of the face and back board, the diameter must be cut, in order to make the grain straight, absolutely cannot string cut, otherwise the wood grain discontinuous phenomenon, the bow will split from these places, and make the whole bow scrapped.
If you want to make a good bow, and the diameter of the log is not big, you can cut the log into the required length first, and then use the ax to cut along the grain. In this way, you can make the rod along the grain, and the effect will be more ideal than the diametrically cut plate. According to the cut plate, after a few years of natural drying, so that its moisture content down to about 6%, to draw lines, sawed into a single bow material.
When drawing the bow head and the side outline of the bow rod on the plate, we must pay attention to make the wood grain straight, in order to create good conditions for the future processing, and make the bow rod not out of shape. On the contrary, where the wood texture is irregular or broken, the bow rod is easy to be deformed, and the bending strength and elasticity of the bow are not durable.The prepared material shall be 740 mm in length, 10.5 mm in width and 23 mm in thickness.
Making thick blank is on the prepared bow bar material (the bow bar is straight at this time), rough machining with various tools, the rod body is roughened and trimmed into a round shape, the diameter of each part is thicker than the bow bar made, leaving a margin for finishing. In roughing, always hold the bow in your hand until it is ready to bend. Its weight, the sapwood rod is generally 39-42 grams. If the bow is made in square shape, the body of the rod should be trimmed into a round shape before making a thick blank.
Student Violin Bow
After the violin is a well-known musical instrument, the most important part of the violin is the bow. Many people will ignore this seemingly low-key, thinking it is just an accessory of the violin, but the bow is not as simple as we imagine. Physically, the bow is a small spring system, but from a more rational point of view, the only connection between a person and a stringed instrument must be established by the bow.
Product Advantages
1. Brazil Wood
The bow is easier to shape than the instrument itself. The craftsman first cuts the red board into strips, each of which must have a quadrilateral cross section. To give the bow a certain arc, it is formed in inches by heating with an alcohol lamp until it reaches its standard shape. When it cools down, a radian is formed, and it generally does not return to its original straightness. The bow industry calls this the "wonderful memory of Brazilian mahogany" -- because the spring system is not released for even a year, and if you gently heat it, the bow will quickly return to its original shape. Because this Brazilian wood has feel comfortable, flexibility is beautiful, not easy deform a bit.
2. Mongolian White Horsetail
After manual selection, the Mongolian white horsetail is slightly bleached, which does no harm to the inner and outer structure of the horsetail and has a bright and clean appearance. Therefore, high toughness, sufficient quantity, easy to wear, not easy to break, friction long service life, good timbour effect, about 220 arch hairs. Mongolian white horsetail and natural color horsetail are classy horsetail with beautiful uniform appearance, strong pulling force and plump wool scales, which should not be broken in use. The diameter of each horsetail is between 14 and 20 silvery meters.
3. Enony Tail Bank
Ebony is used as the raw material for the tail bank. It is matched with metal accessories and can be set with clear texture. The bow wool depot is 44-44.5 mm long, 12.5-13 mm wide and 19.5-20.5 mm high. Make sure that the upper grooves fit tightly with the bow rod, the middle gaskets also fit closely with each other, and the T-nut is mounted at the center. After assembly, turning the adjusting screw can make the bow hair tensioned or loosened, which can increase the weight of the bow root.
4. Styling And Coating
Derhyme uses the method of baking bending to finalize the design, through baking to adjust the bow bending and elasticity. Experienced Derhyme workers flexibly master the highest point of the inner arc, ensuring the bending degree and appropriate elasticity of the bow. After the bow head and tail are complete, a protective coat of paint is applied to the outside of the bow shaft. It increases the service life of the bow and will not cause irregular deformation if used for a long time.
Product Specification
Product Name | Derhyme student violin bow |
Product Model | V10201-1 |
Product Size | 4/4、3/4、1/2、1/4、1/8、1/16 |
Bow Material | Brazil wood |
A Hand Material | Sheepskin package |
Tail Bank | Ebony |
Accessories Material | Copper |
Style | Violin bow |
Product Size
Product Show
Product List
Preparation for making violin bow
There are many kinds of wood for making violin bow and bow. You can choose different raw materials according to the grade. In the wood, you first select the material for preparing the rod and then prepare the material. The material preparation is to cut the log into planks. The sawing method is the same as the making of the face and back board, the diameter must be cut, in order to make the grain straight, absolutely cannot string cut, otherwise the wood grain discontinuous phenomenon, the bow will split from these places, and make the whole bow scrapped.
If you want to make a good bow, and the diameter of the log is not big, you can cut the log into the required length first, and then use the ax to cut along the grain. In this way, you can make the rod along the grain, and the effect will be more ideal than the diametrically cut plate. According to the cut plate, after a few years of natural drying, so that its moisture content down to about 6%, to draw lines, sawed into a single bow material.
When drawing the bow head and the side outline of the bow rod on the plate, we must pay attention to make the wood grain straight, in order to create good conditions for the future processing, and make the bow rod not out of shape. On the contrary, where the wood texture is irregular or broken, the bow rod is easy to be deformed, and the bending strength and elasticity of the bow are not durable.The prepared material shall be 740 mm in length, 10.5 mm in width and 23 mm in thickness.
Making thick blank is on the prepared bow bar material (the bow bar is straight at this time), rough machining with various tools, the rod body is roughened and trimmed into a round shape, the diameter of each part is thicker than the bow bar made, leaving a margin for finishing. In roughing, always hold the bow in your hand until it is ready to bend. Its weight, the sapwood rod is generally 39-42 grams. If the bow is made in square shape, the body of the rod should be trimmed into a round shape before making a thick blank.
Copyright Henan Derhyme Musical Instrument Co.,Ltd. All rights reserved
